Script started on Sat Jun 3 15:59:25 2023 uaa@framboise:~$ epicon -s 115200 -l /dev/ttyU0 ** Welcome to epicon Version-5.2 Copyright Isamu Yamauchi compiled:Mar 28 2021 ** exec shell ~! send binary files ~f send break ~b call rz,sz,sx,rx ~rz,~sz,~sx,~rx call kermit ~sk,~rk external command ~C change speed ~c exit ~. Connected /dev/ttyU0 [113]HELLO! BOOT0 is starting! [116]BOOT0 commit : 3ae35eb [119]set pll start [122]periph0 has been enabled [125]set pll end [127]unknow PMU [128]unknow PMU [130]PMU: AXP1530 [137]vaild para:8 select dram para0 [141]board init ok [143]DRAM BOOT DRIVE INFO: V0.648 [146]the chip id is 0x2000 [149]chip id check OK [154]DRAM_VCC set to 1500 mv [160]write_leveling error [163calibration error [168]write_leveling error [171]read_calibration error [177]write_leveling error [180]read_calibration error [186]write_leveling error [189]read_calibration error [194]write_leveling error [197]read_calibration error [203]write_leveling error [206]read_calibration error [212]write_leveling error [215]read_calibration error [220]write_leveling error [223]read_calibration error [229]write_leveling error [232]read_calibration error [238]write_leveling error [241]read_calibration error [243]retraining final error [249]write_leveling error [252]read_calibration error [258]write_leveling error [260]read_calibration error [266]write_leveling error [269]read_calibration error [275]write_leveling error [277e_leveling error [286]read_calibration error [291]write_leveling error [294]read_calibration error [300]write_leveling error [303]read_calibration error [308]write_leveling error [311]read_calibration error [317]write_leveling error [320]read_calibration error [325]write_leveling error [328]read_calibration error [331]retraining final error [337][AUTO DEBUG]16 bit,2 ranks training success! [348]DRAM CLK =720 MHZ [350]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [358]Actual DRAM SIZE =1024 M [361]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4001001, dram_tpr13 = 6041 [374]DRAM simple test OK. [377]rtc standby flag is 0x0, super standby flag is 0x0 [382]dram si024 [385]card no is 0 [387]sdc94][mmc]: b mmc 0 bias 0 [402][mmc]: Wrong media type 0x0 [405][mmc]: ***Try SD card 0*** [414][mmc]: HSSDR52/SDR25 4 bit [417][mmc]: 50000000 Hz [419][mmc]: 14768 MB [421][mmc]: ***SD/MMC 0 init OK!!!*** [522]Loading boot-pkg Succeed(index=0). [526][mmc]: b mmc 0 bias 0 [528]Entry_name = u-boot [537]Entry_name = monitor [541]Entry_name = dtbo [544]Entry_name = dtb [548]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):05d6c57 NOTICE: BL3-1: Built : 13:35:35, 2021-10-28 NOTICE: BL3-1 commit: 8 NOTICE: cpuidle init version V2.0 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-g23fdfbb-dirty (Dec 02 2022 - 18:03:14 +0800) Allwinner Technology [00.626]CPU: Allwinner Family [00.628]Model: sun50iw9 I2C: ready [00.633]DRAM: 1 GiB [00.636]Relocation Offset is: 35ebf000 [00.673]secure enable bit: 0 [00.676]pmu_axp152_probe pmic_bus_read fail [00.680]PMU: AXP1530 [00.686]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.694]drv_disp_init [00.725]__clk_enable: clk is null. [00.731]drv_disp_init finish [00.734]gic: sec monitor mode [00.764]flash init start [00.766]workmode = 0,storage type = 1 [00.770]MMC: 0 [00.771][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.777][mmc]: get sdc_type fail and use default host:tm1. [00.788][mmc]: Using default timing para [00.792][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.809][mmc]: card_caps:0x3000000a [00.812][mmc]: host_caps:0x3000003f [00.816]sunxi flash init ok [00.820]Loading Environme OK [00.835]Item0 (Map) magic is bad [00.838]the secure storage item0 copy0 magic is bad [00.843]Item0 (Map) magic is bad [00.846]the secure storage item0 copy1 magic is bad [00.851]Item0 (Map) magic is bad [00.853]usb burn from boot delay time 0 weak:otg_phy_config [00.867]usb prepare ok [01.037]usb sof ok [01.038]usb probe ok [01.040]usb setup ok set address 0xf set address 0xf ok [04.046]do_burn_from_boot usb : have no handshake [04.050]boot_gui_init:start ** Unrecognized filesystem type ** tcon_de_attach:de=0,tcon=2[04.334]boot_gui_init:finish [04.338]bmp_name=bootlogo.bmp 2764854 bytes read in 117 ms (22.5 MiB/s) [04.477]update dts ** Unrecognized filesystem type ** [04.491]load file(ULI/factory/rootwait init.txt) error. ** Unrecognized filesystem type ** [04.508]load file(ULI/factory/snum.txt) error. ** Unrecognized filesystem type ** [04.525]load file(ULI/factory/mac.txt) error. ** Unrecognized filesystem type ** [04.541]load file(ULI/factory/wifi_mac.txt) error. ** Unrecognized filesystem type ** [04.558]load file(ULI/factory/bt_mac.txt) error. ** Unrecognized filesystem type ** [04.575]load file(ULI/factory/selinux.txt) error. ** Unrecognized filesystem type ** [04.591]load file(ULI/factory/specialstr.txt) error. [04.607]update part info [04.641]update bootcmd [04.643]No ethernet found. Hit any key to stop autoboot: 0 Wrong Image Format for bootm command ERROR: can't get kernel image! => printenv boot_fastboot=fastboot boot_from_partion=boot boot_normal=sunxi_flash read 45000000 boot;bootm 45000000 boot_recovery=sunxi_flash read 45000000 recovery;bootm 45000000 bootargs=earlyprintk=sunxi-uart,0x05000000 initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p4 rootwait init=/init partitions=bootloader@mmcblk0p1:env@mmcblk0p2:boot@mmcblk0p3:super@mmcblk0p4:misc@mmcblk0p5:recovery@mmcblk0p6:cache@mmcblk0p7:vbmeta@mmcblk0p8:vbmeta_system@mmcblk0p9:vbmeta_vendor@mmcblk0p10:metadata@mmcblk0p11:private@mmcblk0p12:frp@mmcblk0p13:empty@mmcblk0p14:media_data@mmcblk0p15:Reserve0@mmcblk0p16:UDISK@mmcblk0p17 cma=64M snum=4c0014402280c931c90 mac_addr= wifi_mac= bt_mac= selinux=0 specndroidboot.serialno=4c0014402280.secure_os_exist=0 gpt=1 uboot_message=2018.05-g23fdfbb-dirty(12/02/2022-18:03:14) disp_reserve=3686400,0x7bf27840 bootreason=unknow bootcmd=run setargs_mmc boot_normal bootdelay=0 bootreason=unknow cma=64M console=ttyS0,115200 disp_reserve=3686400,0x7bf27840 earlyprintk=sunxi-uart,0x05000000 fastboot_key_value_max=0x8 fastboot_key_value_min=0x2 fdtcontroladdr=7be7ccc0 fileaddr=40000000 filesize=2a3036 init=/init initcall_debug=0 initrd_end=0 initrd_start=0 keybox_list=hdcpkey,widevine loglevel=8 mmc_root=/dev/mmcblk0p4 nand_root=/dev/nand0p4 nor_root=/dev/mtdblock4 partitions=bootloader@mmcblk0p1:env@mmcblk0p2:boot@mmcblk0p3:super@mmcblk0p4:misc@mmcblk0p5:recovery@mmcblk0p6:cache@mmcblk0p7:vbmeta@mmcblk0p8:vbmeta_system@mmcblk0p9:vbmeta_vendor@mmcblk0p10:metadata@mmcblk0p11:private@mmcblk0p12:frp@mmcblk0p13:empty@mmcblk0p14:media_data@mmcblk0p15:Reserve0@mmcblk0p16:UDISK@mmcblk0p17 recovery_key_value_max=0x13 recovery_key_value_min=0x10 selinux=0 setargs_mmc=setenv bootargs earlyprintk=${earlyprintk} initcall_debug=${initcall_debug} console=${cnit} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} selinux=${selinux} specialstr=${specialstr} gpt=1 setargs_nand=setenv bootargs earlyprintk=${earlyprintk} initcall_debug=${initcall_debug} console=${console} loglevel=${loglevel} root=${nand_root} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} selinux=${selinux} specialstr=${specialstr} gpt=1 setargs_nor=setenv bootargs earlyprintk=${earlyprintk} initcall_debug=${initcall_debug} console=${console} loglevel=${loglevel} root=${nor_root} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} selinux=${selinux} specialstr=${specialstr} gpt=1 snum=4c0014402280c931c90 Environment size: 2858/131068 bytes => version U-Boot 2018.05-g23fdfbb-dirty (Dec 02 2022 - 18:03:14 +0800) Allwinner Technology arm-linux-gnueabi-gcc (Linaro GCC 7.2-2017.11) 7.2.1 20171011 GNU ld (Linaro_Binutils-2017.11) 2.28.2.20170706 => bdinfo arch_number = 0x00000000 boot_params = 0x40000100 DRAM bank = 0x00000000 -> start = 0x40000000 -> size = 0x40000000 current eth = unknown ip_addr = baudrate = 115200 bps TLB addr = 0x7FFF0000 relocaddr = 0x7FEBF000 reloc off = 0x35EBF000 irq_sp AE0 fdt_blob = 7be7ccc0 => Disconnected uaa@framboise:~$ exit exit Script done on Sat Jun 3 16:00:45 2023