Script started on Fri Jun 30 19:01:16 2023
uaa@framboise:~$ epicon -s 115200 -l /dev/ttyU0

** Welcome to epicon Version-5.2 Copyright Isamu Yamauchi compiled:Mar 28 2021 **
      exec shell         ~! 
      send binary files  ~f
      send break         ~b
      call rz,sz,sx,rx   ~rz,~sz,~sx,~rx
      call kermit        ~sk,~rk
      external command   ~C 
      change speed       ~c 
      exit               ~. 
      Connected /dev/ttyU0 

[154]HELLO! BOOT0 is starting!
[157]BOOT0 commit : a00ebdcb84
[160]set pll start
[163]periph0 has been enabled
[166]set pll end
[169]unknow PMU
[171]unknow PMU
[175]PMU: AXP1530
[179]vaild para:1  select dram para0
[183]board init ok
[185]enable_jtag
[187]DRAM BOOT DRIVE INFO: V0.651
[190]the chip id is 0x2000
[193]chip id check OK
[215]DRAM_VCC set to 1500 mv
[221]write_leveling error 
[224]read_calibration error 
[230]write_leveling error 
[233]read_calibration error 
[239]write_leveling error 
[242]read_calibration error 
[248]write_leveling error 
[250]read_calibration error 
[256]write_leveling error 
[259]read_calibration error 
[265]write_leveling error 
[268]read_calibration error 
[274]write_leveling error 
[277]read_calibration error 
[283]write_leveling error 
[286]read_calibration error 
[292]write_leveling error 
[295]read_calibration error 
[301]write_leveling error 
[304]read_calibration error 
[306]retraining final error 
[312]write_leveling error 
[315]read_calibration error 
[321]write_leveling error 
[324]read_calibration error 
[330]write_leveling error 
[333]read_calibration error 
[338]write_leveling error 
[341]read_calibration error 
[347]write_leveling error 
[350]read_calibration error 
[356]write_leveling error 
[358]read_calibration error 
[364]write_leveling error 
[367]read_calibration error 
[373]write_leveling error 
[376]read_calibration error 
[382]write_leveling error 
[384]read_calibration error 
[390]write_leveling error 
[393]read_calibration error 
[396]retraining final error 
[402][AUTO DEBUG]16 bit,2 ranks training success!
[414]DRAM CLK =720 MHZ
[416]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4)
[424]Actual DRAM SIZE =1024 M
[427]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4001001, dram_tpr13 = 6041
[440]DRAM simple test OK.
[442]rtc standby flag is 0x0, super standby flag is 0x0
[448]dram size =1024
[451]Use rtc to store dram tuning para
[454]card no is 0
[456]sdcard 0 line count 4
[459][mmc]: mmc driver ver 2021-10-12 13:56
[463][mmc]: b mmc 0 bias 0
[471][mmc]: Wrong media type 0x0
[475][mmc]: ***Try SD card 0***
[483][mmc]: HSSDR52/SDR25 4 bit
[486][mmc]: 50000000 Hz
[489][mmc]: 14768 MB
[491][mmc]: ***SD/MMC 0 init OK!!!***
[591]Loading boot-pkg Succeed(index=0).
[595][mmc]: b mmc 0 bias 0
[598]Entry_name        = u-boot
[607]Entry_name        = monitor
[611]Entry_name        = dtbo
[613]Entry_name        = dtb
[617]mmc not para
[619]Jump to second Boot.
NOTICE:  BL3-1: v1.0(debug):05d6c57
NOTICE:  BL3-1: Built : 13:35:35, 2021-10-28
NOTICE:  BL3-1 commit: 8
NOTICE:  data: 50 0 0 0
NOTICE:  hardware error 3
PANIC in EL3 at x30 = 0x0000000048001edc
x0 =		0x0000000000000003
x1 =		0x0000000005000000
x2 =		0x0000000000000060
x3 =		0x0000000000000001
x4 =		0x0000000000000000
x5 =		0x00000000480195d8
x6 =		0x00000000480196c0
x7 =		0x00000000000000b3
x8 =		0x000000004803b000
x9 =		0x0000000048000168
x10 =		0x00000000480072a8
x11 =		0x0100011200000000
x12 =		0x9876c8c400000000
x13 =		0x03370975e2694b58
x14 =		0x80050c88b2016a29
x15 =		0x6ac1802577c086a4
x16 =		0x25424f0008723607
x17 =		0x7262cd0800021400
x18 =		0x1ba22ca60002aa15
x19 =		0x000000004801700a
x20 =		0x0000000048000000
x21 =		0x0000000008100044
x22 =		0x24490105b1b06508
x23 =		0x0164643a22d11515
x24 =		0x91811882012b8709
x25 =		0x0900b00869040109
x26 =		0x41ec04e900800294
x27 =		0x00c72d8008133890
x28 =		0x0980244c16ac2862
x29 =		0x00000000480196d0
scr_el3 =		0x0000000000000030
sctlr_el3 =		0x0000000000cd183f
cptr_el3 =		0x0000000000000000
tcr_el3 =		0x000000008081351f
daif =		0x00000000000002c0
mair_el3 =		0x00000000000004ff
spsr_el3 =		0x00000000000001cd
elr_el3 =		0x53a2030c0c21d562
ttbr0_el3 =		0x000000004803bb40
esr_el3 =		0x0000000018525009
far_el3 =		0x002b884072e82341
spsr_el1 =		0x00000000000001cd
elr_el1 =		0x00000007b854159e
spsr_abt =		0x00000000020c8403
spsr_und =		0x0000000018000610
spsr_irq =		0x00000000420bb124
spsr_fiq =		0x00000000820210fa
sctlr_el1 =		0x0000000000c50838
actlr_el1 =		0x0000000000000000
cpacr_el1 =		0x0000000000000000
csselr_el1 =		0x0000000000000000
sp_el1 =		0x098404c94654033e
esr_el1 =		0x0000000004b4802c
ttbr0_el1 =		0x2448406ba698c002
ttbr1_el1 =		0x22538a45ab387948
mair_el1 =		0x44e048e000098aa4
amair_el1 =		0x0000000000000000
tcr_el1 =		0x0000000000000000
tpidr_el1 =		0x481420023b0d9606
tpidr_el0 =		0x9211584a50464090
tpidrro_el0 =		0x082a114045e604a2
dacr32_el2 =		0x00000000ba2020a3
ifsr32_el2 =		0x0000000000000424
par_el1 =		0x000000ac7106a896
mpidr_el1 =		0x0000000080000000
afsr0_el1 =		0x0000000000000000
afsr1_el1 =		0x0000000000000000
contextidr_el1 =		0x0000000000000000
vbar_el1 =		0x0000000000000000
cntp_ctl_el0 =		0x0000000000000002
cntp_cval_el0 =		0xdeaede6f5436694f
cntv_ctl_el0 =		0x0000000000000002
cntv_cval_el0 =		0x200298bd44d47df4
cntkctl_el1 =		0x0000000000000000
fpexc32_el2 =		0x0000000000000700
sp_el0 =		0x00000000480196d0
cpuectlr_el1 =		0x0000000000000040

Disconnected
uaa@framboise:~$ 
exit

Script done on Fri Jun 30 19:01:27 2023